We strongly recommend getting a 3-hole punch machine as it is the easiest way to bind books at home. It is incredibly easy to bind a book at home as long as you have the right tools. But for the most part, you simply need to punch holes on the paper and screw them together. Frequently Asked QuestionsĮach method is different, and so depending on what way you use, the steps might be different. However, when it comes to durability, you might not be so pleased with the results. It is relatively cheap and efficient at the same time. The method is commonly used for binding textbooks. This is the best method if you don’t have much time and don’t feel like going through all the techniques we’ve gone through so far. Simply take the paper out, and then you will notice that now you have three holes on your paper. You will hear a clicking sound when you do that.
Make sure to slide it all the way back to the stopper.įrom there, you just need to hold the paper and then press down on the 3-hole punch. You simply need to place the paper in-between those three spots. As the title suggests, this machine has three holes where the unit will punch holes in the paper. This is by far the easiest bookbinding method. This method is quite useful for those folks that don’t have much time but still want a powerful way to bind books. After that, you can safely place it on your shelf!Īs you can tell, this process is quite simple. Take the documents out and put them in the cooling rack for a few minutes.
Now, you need to wait a few minutes until you hear a beeping sound. Now, put the documents inside the machine, and then select the time cycle.įrom doing this, we’re telling the machine to heat up the glue and attach the pages. So, get your stack of papers and then put them in your cover. First of all, to bind a book using a thermal binding tool, you need to cover the spine with glue. Unlike other methods where you have to do everything manually, thermal binding makes it much easier, and you don’t have to go through all those time-consuming processes.Īlthough using a thermal binding machine might seem quite hard to use, it’s actually quite simple. You don’t need to put in much effort either. Thermal binding does not require much time. Finally, secure the book with rubber bands and let it dry overnight.It is one of the most efficient methods you can use to bind your books. Close the book and run the bone folder down the outside of the spine.
DIGIPOD PRINTING BOOK BINDING FREE
Rub the free tab on the tape onto the inside of the cover using the bone folder. Apply book adhesive to the other two tabs on the tape, then bring the cover up so it aligns with the seam on the tape. Then, place one piece of waxpaper over the endpaper and one piece over the spine. Rub both tabs with a bone folder and let them dry overnight. Next, stick one of the tape tabs to the spine of the text block and stick the other tab to the endpaper. Cut a piece of single-stitched binder tape that’s the same length as the text block and apply book adhesive to one side with a brush. To repair a broken hinge, first fully remove the hinge from the book so it’s easier to work with. Place another wooden board on top followed by 10 pounds (4 ½ kg) of weight. Place the book on a wooden board and align knitting needles that are thicker than the cover with the outer hinges of the book. Now close the book and run the bone folder down the hinge on the outside. Then, place a piece of wax paper between the cover and endpaper to protect it from the adhesive. Partially open the cover and use a bone folder to press the endpaper into the hinge of the book. Spread book adhesive around inside of the gap using a knitting needle, then lay the book flat and square the block of pages. First, stand the book up and use your finger to open the gap between the spine and pages. If there’s a gap between the spine and pages of your book, you can use book adhesive to close it. Stack something heavy on top of the book and let it dry for 24 hours.
Then, align the loose pages over the glue and press them into the spine. Remove the loose pages and spread a thin layer of glue over the spine using a popsicle stick. If pages have fallen out of your book, you can use an acid-free book or binding glue to reattach them.
The best way to repair a book’s binding depends on what’s wrong with it.